Meet your new smart, small and versatile encoder

(yes, nothing less)


Meet PYKO-in: the cost-effective stereo IP audio encoder that makes no compromise with sound quality. Used as a standalone device, PYKO-in will gladly convert analog audio sources into an IP audio stream sent to one or several destinations. Typical applications include STL, WEB radio encoding, background music and paging or intercom over IP, all with a crisp, sheer sound. Combined with its buddy PYKO-out, PYKO-in is a cost-effective solution for establishing IP audio links.

Cost effective STL

Smart audio IP encoder

No compromise on audio quality 

Balanced analog audio I/Os, +18dBu max level

Easy as A, B

Configuration & control

Key features

Analog I/Os
Standard IP audio streaming
Tunneling of auxiliary data (serial, GPI’s)
Remote control via WEB GUI, ASCII commands over TCP or via serial port


Never bored, never tired 

your PA fellow 

Stream your radio show from home

Setup of web radios,

easy as pie


  • Size (mm) / weight (g): 140 x 41 x 145 mm  / 434g
  • Power supply: External 24VDC +/-20%
  • Operating temperature / humidity: 0°C to 55°C / 0% to 70% non condensing
Balanced analog audio I/Os
  • 1 stereo input / 1 mono I/O  in full duplex-mode
  • Left input Mic/line with 12V phantom power
  • E.I.N (48 kHz, G=39 dB, Z=200 Ohms) <-115 dBm
  • Maximum level / impedance
    • Inputs: +4 dBu / +18 dBu / > 10 Kohms
    • Mic level/impedance -2 dBu > 10 kohms
    • Left output (full-duplex mode only): +4 dBu / +18 dBu / < 100 ohms
  • Frequency response: 0/-2 dB <20-20000Hz>
  • THD + Noise:
    • input: < – 84dB @ -1 dBFS <20-20000Hz>
    • output: < – 84 dB @ -2dBFS  <20-20000Hz>
  • SNR: <- 98 dB <20-20000Hz>
Audio formats
  • PCM 16bits, G.711, G722
  • MPEG Layer 3 (VBR up to 192 kBit) (not in full-duplex)
  • Analog audio: Euroblock connector
  • Network: 10/100 Mbit Ethernet (RJ45)
  • RS232: SubD 9-pin male
  • GPIOs: Euroblock connector
  • Headphone out: 3.5 mm Jack



I can't access to the PYKO web pages anymore, what can I do ?

At first you can try to reset it to the factory settings by pressing 5 seconds with a tip in the hole which is in the middle of the PYKO front panel. If it not fix the issue, ask for the PYKO rescue procedure to the technical support team.

How can I use a USB memory stick on PYKO-out to play sound files ?

PYKO-out is able to play a playlist stored on a USB memory stick. This stick can be connected either to the front panel USB port, or to the internal USB port. These two USB ports can’t be used simultaneously. The USB stick must be FAT 16 formatted.

The firmware to be used is the Playout-extended firmware. The playlist must be an m3u playlist, and its name has to be entered in the URL field of the decoding priority 2 or decoding priority 3 (example: backup-playlist.m3u).

The mp3 sound files and playlist files (stream priority 3) must be located in the /bk directory of USB stick. The playlist and audio file names must have a maximum of 24 characters.

The safe characters are pure ASCII letters (a-z A-Z), digits (0-9) and underscore (_). The playslit is played when no audio source is available on the previous decoding priority(ies).

My PYKO goes ON and OFF as if there was an issue with the power supply.

You may want to check the power supply connector on the rear panel of PYKO (PWR connector).

The conductive core of this connector is split in two parts: insert a thin device (like a screwdriver) between the two parts of the conductive core to slightly enlarge the space and minimize the risk of unexpected ON/OFF cycles due to too little space between these parts.

How to decode an RTP stream on PYKO OUT?

The parameters of the stream(s) to be decoded have to be configured from the Audio menu, stream priority 1, stream priority 2, stream priority 3 WEB pages.

The URL field allows declaring the stream to be decoded on the selected priority. For receiving a unicast stream (point to point link) the syntax is: rtp://>. Example: rtp://

For receiving a multicast stream (point to multipoint link) the syntax is: rtp://multicast IP@:port>. Example: rtp://

What value must be set for the parameter “Latency” on PYKO-out?

The latency value is selectable from 1 to 10. This value is to be set according to the network jitter and the audio format. In MPEG audio formats, this value must be set to a minimum value of 6.

For other formats (PCM, G711), this latency parameter can be set to low values on high quality network (low jitter). PYKO-out displays in real time the jitter-margin on its WEB page. Adjust the Latency value so that the displayed jitter margin value remains higher than 0.

Can PYKO decode the AAC format?

The AAC audio compression is supported by PYKO-out only with the firmware “Playout-extended”. Supported AAC flavors are AAC-LC, HE-AACv1 (limited to 32 kHz), and HE-AACv2 (limited to 32 kHz). The AAC must be in ADTS mode. The RTP payload must be 126. Note that PYKO-in does not support AAC encoding.

How to decode a web radio with PYKO?

The PYKO OUT EXTENDED firmware decodes a stream from Shoutcast or Icecast servers. The supported formats are MPEG and AAC. Type the URL provided by the web radio server. Example:

Is MP3 variable bit rate supported in PYKO ?

Yes, the constant bit rate and the variable bit rate are supported for MP3, from streams and files.